SovAvto Website.
K-703MT-3S-0 (earth-hauler)
K-703MT-E'T-1 (single bucket excavator)
K-703MT-KT-16 (hydraulic crane)
K-703MTU-60/80G (lifting installation for oil wells)
| Model | K-703MT-3S-0 |
| Seating | 1 |
| Net-weight, kg [lb] | 23,000 [50,600] |
| Full load weight, kg [lb] | - |
| Load weight, kg [lb] | 18,000 [39,600] |
| Body or bucket volume, m3 | 12 |
| Pulling torque, N·m [lb·ft] | - |
| Unloading height, mm [in.] | - |
| Maximum digging depth, m [yards] | - |
| Total trailer weight, kg [lb] | - |
| Length, mm [in.] | - |
| Width, mm [in.] | - |
| Height, mm [in.] | - |
| Base, mm [in.] | - |
| Minimal clearance, mm [in.] | - |
| Minimal radius of turn, m [yards] | - |
| Maximum incline, degrees | - |
| Maximum list, degrees | - |
| Maximum forward travel speed, km/h [mi/h] | 39 [24] |
| Maximum reverse travel speed, km/h [mi/h] | - |
| Maximum horsepower, hp [kW] | 335 [246] |
| Maximum torque, N·m [lb·ft] | - |
| Engine displacement, liters [cc] | - |
| Compression ratio | - |
| Gear ratios | - |
| Main gear ratio | - |
| Mileage, liters/100km [mi/gal] | - |
| Acceleration time from 0-100 km/h [62 mi/h], seconds | - |
| Breaking distance, m [yards] | - |
| Fuel tank capacity, liters [gal] | - |
| Years of production | ? |
| Type of engine | - |
| Bore/Stroke, mm [in.] | - |
| Wheel formula | 6 X ? |
| Pictures | 18 KB (color, side view [96]) |
Below are short techincal descriptions and specifications that distinguish all of the tractors, machines on this page.
K-703MT-3S-0 earth-hauler is intended for transport of crushed stone (fraction not more then 70 mm [2.7 in.], clay (including saline soil) in cross-country conditions. For technical info and photos, see table above.
K-703MT-E'T-1 single-bucket excavator is intended for working with soil of I-IV categories in cross-country conditions.
| volume of bucket (m3) | 1.25 |
| maximum digging depth (m) | 4.5 |
| maximum unloading height (m) | 6.6 |
| maximum travel speed (km/h) | 25 |
| net mass (kg) | 36,200 |
| photo | (19 KB color, rear view [96]) |
K-703MT-KT-16 is a hydraulic crane intended for loading and unloading functions in industrial, civil and roadway construction. Can be uesd effectively in cross-country conditions.
| maximum load on crane arm (kg) | 16,000 |
| maximum jib length (m) | 18 |
| maximum lifting heigth (m) | 22 |
| maximum transport speed (km/h) | 25 |
| maximum power (horsepower) | 266 [198.5] |
| net mass (kg) | 34,600 |
| photo | (23 KB color, side view [96]) |
K-703MTU-60/80G is a lifting installation intended for setting up of pumping/compressing and boring pipes in instances of repairs of crude oil and gas wells.
| nominal load (kg) | 60,000 |
| maximum load (kg) | 80,000 |
| speed of non-stepped regulating of tackle block I mode (m/s) | 0.18-0.44 |
| speed of non-stepped regulating of tackle block II mode (m/s) | 0.47-0.9 |
| maximum load of the hydro-winch (cable tension) kN | 147.0 |
| maximum load of the auxilirary winch (cable tension) kN | 20.0 |
| maximum load of the "Sputnik" winch (cable tension) kN | 3.2 |
| torque of the pipe key (N*m) | 4,000-12,000 |
| maximum load on the spider (kg) | 80,000 |
| maximum torque on the shaft of the rotor (H*m) | 1200 |
| engine power (horsepower) | 266 |
| net mass (kg) | 43,000 |
| photo | (23 KB color, front view [96]) |
Page created on Saturday, September 04, 1999. Page last updated on Friday, May 31, 2002 05:36:05 PM EST.
